SpeedDome Ultra VII Day/Night Camera Dome RAS917LS RAS917LS-1 RAS917WLS RAS917WLS-1 Configuration Utility Operator’s Manual 8200-0184-04 D
NOTES: viii SpeedDome Ultra VII Day/Night Operator's Manual
Command Summary The following table lists the commands to operate the configuration utility when the dome is installed in an AD Up-the-Coax (AD-UTC)
Additional AD-UTC Commands The following tables summarize the special commands available when using the dome in an AD-UTC network. These commands are
Supported Controllers The following AD-UTC controllers are compatible with SpeedDome Ultra VII: Controller Presets Patterns Quick Set Menu ADCC020
Quick Set Command / Menu Item Description 0+ : Toggle Quick Set Menu Toggles between displaying and hiding the quick set menu. 1+ : Dome Config Menu
E–6 SpeedDome Ultra VII Day/Night Operator's Manual
APPENDIX F Vicon Command Summary This appendix summarizes the SpeedDome Ultra VII features that are supported by the Vicon protocol. In addition, it
Vicon Command Summary The following table lists the Vicon controller key sequence to control the indicated SpeedDome Ultra VII functions. If you want
If you want to … Use … Reset Dome Run/Pgm switch to PGM Enter 97 Enter Auto Pan Left Limit See Setting Left and Right Auto Pan Scan Limits on pag
Setting Names / Working with Passwords When setting names or entering password information, the screen displays the available characters in the select
Setting the Auto Pan Speed 1. Press and hold A/P key. 2. Move joystick to Pan Right until the desired speed is observed on the monitor. 3. Release t
CHAPTER 1 Using the Dome Configuration Utility The SpeedDome Ultra VII Day/Night camera dome is a 23X optical zoom camera enclosed in a compact dome
In Vicon systems where the domes support RS-485 daisy chaining, daisy chain the SpeedDome Ultra VII domes off the controller or one of the Vicon domes
APPENDIX R Dome Configuration Records Use the pages in this appendix to record the configuration settings for your SpeedDome Ultra VII Day/Night Cam
DOME NUMBER: ___________________ LOCATION: ________________________ Configuration Settings Pan / Tilt / Zoom / Sync Options Menu Item Default Sett
DOME NUMBER: ___________________ LOCATION: ________________________ Set North Position Describe North position: Area Boundaries Up to 16 areas can
DOME NUMBER: ___________________ LOCATION: ________________________ Text Attribute Options Menu Item Default Setting (Choices) Current Setting Ch
DOME NUMBER: ___________________ LOCATION: ________________________ Presets Up to 96 presets may be programmed for each dome. Use this form to desc
DOME NUMBER: ___________________ LOCATION: ________________________ Preset Number Description Assigned Name Preset 49 Preset 50 Preset 51 P
DOME NUMBER: ___________________ LOCATION: ________________________ Dome Information Record the information found on the Dome Information screen h
DOME NUMBER: ___________________ LOCATION: ________________________ NOTES: R–8 SpeedDome Ultra VII Day/Night Operator's Manual
APPENDIX S Software License Agreement By using this software, you accept the terms and conditions of this license agreement. Read this license agreem
What is the Dome Configuration Utility? The Dome Configuration Utility provides a means to setting features for your camera dome via a text overlay m
Customer may make up to 2 copies of the Software solely for back-up and archival purposes. Customer will not remove or modify the copyright and othe
SEC AND ITS SUPPLIERS, EMPLOYEES, AGENTS AND FRANCHISEES WILL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR OTHER DIRECT OR INDIRECT DAMA
NOTES: S–4 SpeedDome Ultra VII Day/Night Operator's Manual
SPEEDDOME ULTRA VII GLOSSARY Alarm Actions The assigned responses for the dome when inputs change from normal to abnormal states. The dome may run a P
Flip To automatically rotate the dome 180° from its current pointing position. See Automatic “Flip” feature. Freeze Frame A feature that allows the c
Peel Button found on some controllers that initiates the Apple Peel pattern. See Apple Peel Pattern. Preset Programmed video scene, based on a speci
Zoom To adjust the magnification of the camera lens to make an object appear closer (larger) or farther away (smaller). See also Zoom stop factors.
INDEX –A– Activating IR mode manually, 3–4 Advanced Shutter Settings Overview, 3–7 Alarm Actions Configuring, 4–3 Area Boundaries Overview, 4–9, 4–10
Scan Types random, 4–18 smooth, 4–18 stepped, 4–18 Setting Scan Limits Pelco protocols, C–5 Settings Overview Alarms, Areas, Home Postion, North Posit
Working with the Dome Configuration Utility Once the Dome Configuration Menu is displayed, you may select a menu item, and then modify the settings yo
Please visit our website for more information www.americandynamics.net © 2003 Sensormatic Electronics Corporation Product specifications subject t
To enter the password using SensorNet, RS-422, or Manchester protocols: 1. Use the Pan/Tilt control to move the highlight the appropriate character.
Exiting the Configuration Utility Under SensorNet, RS-422, and Manchester protocols, you may save your changes and exit the utility from any screen by
Quick Set Command Description 0+Quick Set Toggles between displaying and hiding the quick set menu. 1+ Quick Set Displays the SpeedDome Ultra con
Where To Go Next Now that you understand how to start and work with the Dome Configuration Utility, you are ready to begin changing the settings for y
Chapter Topics Covered Chapter 6: Configuring Language and Password Settings − Choose the language for the menus and prompts − Set a password to l
CHAPTER 2 Configuring Pan, Tilt, Zoom, and Synchronization Options This chapter describes the use of the Pan/Tilt/Zoom/Sync Opts menu. Use this scree
Overview of Pan / Tilt / Zoom/Synchronization Options Screen When Pan/Tilt/Zoom/Sync Opts is selected from the Dome Configuration Menu, the following
Adjusting the Zoom Stop Settings The SpeedDome Ultra VII Day/Night dome includes a 23X optical zoom camera with 10X digital zoom capability. The maxim
Configuring the Line Lock Setting Use the Line Lock setting to prevent vertical rolling or adjust the appearance of overlay text on color monitors. I
Configuring the Freeze Frame Setting If you need to maintain a static image when calling automatic functions, such as presets or patterns, use the Fre
Changing the Freeze Frame Setting 1. Select Pan/Tilt/Zoom/Sync Opts from the Dome Configuration Menu. 2. Move the highlight bar to Freeze Frame. Chan
What To Do Next When you select Exit from the Pan/Tilt/Zoom screen, the Dome Configuration Menu appears. DOME CONFIGURATION MENUPAN/TILT/ZOOM/SYNC OP
NOTES: 2–8 SpeedDome Ultra VII Day/Night Operator's Manual
CHAPTER 3 Configuring Camera Features This chapter describes the settings used to control the camera features. It describes how to change the white b
Adjusting White Balance Settings White balance is normally compensated for by the automatic white balance gain control. In some lighting conditions, y
Changing Automatic White Balance Settings 1. Select Camera Functions from the Dome Configuration Menu. The highlight appears on the Auto White Bal set
SpeedDome® Ultra VII Day/Night Camera Dome Configuration Utility Operator’s Manual Version - 0710-0147-0107
For more information, see the following topics: • Changing the IR Mode Setting • Manually Activating or Deactivating the IR Mode Changing the IR
Understanding Wide Dynamic Range Wide Dynamic Range (WDR) is a feature that allows clear viewing of both bright and low light areas in a scene. Use th
Figure 3–3: Example scene with loading dock door open and iris open adjustment. With WDR enabled, you can see the scenes both inside and outside th
Working with AGC and Open Shutter Settings The SpeedDome Ultra VII Day/Night dome provides settings for compensating for low-light scenes in color: Au
In this example, the dome receives information about the color of the traffic light. While the light is red, the image is relatively static. With the
Configuring AGC and Open Shutter Settings Tip: The current IR mode setting affects which AGC Gain and Open Shutter settings are available. The Rela
What To Do Next When you select Exit from the Camera Functions screen, the Dome Configuration Menu appears. DOME CONFIGURATION MENUPAN/TILT/ZOOM/SYNC
CHAPTER 4 Configuring Alarms, Areas, Home, Privacy Settings, Presets and Scan Limits This chapter describes settings associated with Alarms, Areas, t
Overview of Alarms, Areas, Home, North Position, Preset, Privacy and Scan Limit Settings When Alarms/Areas/Home/Presets/PZ is selected from the Dome C
Configuring Alarm Actions IMPORTANT When operating on Manchester networks, the dome can be programmed to respond to any of the four available alarm
EQUIPMENT MODIFICATION CAUTION Equipment changes or modifications not expressly approved by Sensormatic Electronics Corporation, the party responsible
Setting Alarm Actions IMPORTANT Some controllers allow the alarm actions for domes to be specified at the controller. See the appendixes for inform
Configuring Normal Input States for Alarms IMPORTANT Some controllers allow the normal input states for domes to be specified at the controller. Th
Setting Alarm Input States 1. Select Alarms/Areas/Home/Presets/PZ from the Dome Configuration Menu. 2. Select Set Alarm States. 3. Select the appropr
Setting the Home Position 1. Select Alarms/Areas/Home/Presets/PZ from the Dome Configuration Menu. 2. Select Set Home Position. The highlight bar a
Setting the North Position Direction Indicators permit you to understand the approximate pointing position of the dome to an established reference poi
Programming Area Boundaries If the dome is installed in a location where you can see numerous departments or other identifiable objects, you might wan
Note: When areas are programmed, each area is assigned a default name. Instructions for assigning new names appear in Chapter 5. To program areas
Note: You will receive an error message under the following conditions: • If you attempt to program an area boundary that passes the starting po
From this screen, you can program up to eight Privacy Zones, delete all or specific Privacy Zones, or temporarily hide all Privacy Zones. For more inf
The circled arrows represent the target area on the screen for creating the Privacy Zone. Normally, this target area remains in the center of the scre
TABLE OF CONTENTS PREFACE: BEFORE YOU BEGIN...
Removing or Hiding Privacy Zones If you make an error during programming or no longer require Privacy Zones, individual zones or all Privacy Zones may
Deleting Specific Privacy Zones To delete individual Privacy Zones, use the following procedure. To delete all Privacy Zones, see Deleting All Privacy
Programming Presets If you need to view specific places routinely, you should program presets. A preset is a programmed video scene with automatic pan
PRESETSPRESET XPosition camera with PANTILT, ZOOM and IRISFOCUS FAR to save and exitEXIT 4. Adjust the camera until you see the scene you want to use
Figure 4–6: Left and Right Scan Limits Left Scan Limit Parking Lot Building Dome Right Scan Limit Scan Types Three types of scans may be activated:
A random scan pans randomly between the left and right scan limits. For example, the scan may start at point in the scan, then pan right 40° and pause
Note: Press Focus during steps 3 or 4 to cancel scan limit programming. 3. Adjust the pan position of the dome to set the left scan limit. Press
CHAPTER 5 Configuring Text Displayed On-Screen This chapter describes how to modify settings related to text displayed by the dome. It includes setti
Displaying or Hiding Status Information You can choose to display the status of the zoom setting, auto focus, and auto iris. This information will app
Displaying or Hiding All Name Information The dome provides the ability to display the dome name, the area where the dome is pointing, the name of the
CHAPTER 7: DISPLAYING DOME INFORMATION...7–1 Unde
Displaying Diagnostic Tests During Reset You can choose to have dome diagnostic tests run whenever the dome resets. The diagnostic information display
Displaying Direction Indicators Direction Indicators let you know the approximate pointing direction of the dome in relation to an established point c
Figure 5–5 represents pointing the dome precisely at 225° from North (Southwest) with a tilt of 25° below the virtual horizon. Panning to the left poi
Changing the Display of Selected Name Information 1. Select On-Screen Text Display from the Dome Configuration Menu. 2. Move the highlight to Name Co
Setting or Changing Names 1. Select On-Screen Text Display from the Dome Configuration Menu. 2. Select Name Configuration Menu. The Name Configuratio
7. Move the blinking highlight around the available characters. When the correct character is highlighted, press Focus to select it. If you make a mi
Figure 5–7: Examples of text attributes If the video background is light, enable character outlines. If on-screen text obscures the video being displ
What To Do Next When you select Exit from the On-Screen Text Display screen, the Dome Configuration Menu appears. Figure 5–8: Dome Configuration Menu
NOTES 5–12 SpeedDome Ultra VII Day/Night Operator's Manual
CHAPTER 6 Configuring Language and Password Settings This chapter explains how to change the language for dome messages and text, and how to set and
PREFACE Before You Begin This preface provides important information that you should be familiar with before using the SpeedDome Ultra VII Day/Night c
Selecting a Language for Dome Messages and Prompts The dome supports menus, status information and prompts in English, Spanish, French, German, Italia
4. Do one of the following: • To continue with changing the language, select Continue. The dome automatically resets. To verify the language change,
Enabling or Disabling Password Protection Pas rotect e password: Select an age/Password from the Dome Configuration Menu. 3. sword protection. h What
CHAPTER 7 Displaying Dome Information This chapter explains how to display dome information and operating information. In This Chapter • Understandi
Viewing Dome Operating Statistics When Dome Statistics is selected from the Dome Information screen, the following information is displayed: DOME STAT
What To Do Next When you select Exit from the Dome Information screen, the Dome Configuration Menu appears. DOME CONFIGURATION MENUPAN/TILT/ZOOM/SYNC
NOTES: SpeedDome Ultra VII Day/Night Operator's Manual 7–4
APPENDIX A SensorNet and RS-422 Command Summary This appendix summarizes the SensorNet and RS-422 controller commands used with the Configuration Uti
Command Summary The following table lists the commands to operate the configuration utility when the dome is installed in a SensorNet or RS-422 envir
Supported Controllers and Matrix Switching Systems This section provides information about the SensorNet and RS-422 controllers and matrix switchers t
What’s In This Manual? The SpeedDome Ultra VII Day/Night Camera Dome Configuration Utility Operator's Manual is organized as follows: • Chapter
VM32/AD32 Supported Protocols SensorNet RS-422 (1) Maximum Presets 96 – SensorNet 4 – RS-422 Maximum Patterns (2)3 Quick Set Menu Not supported
AD168 Supported Protocols SensorNet (1)RS-422 (1) or (2) Maximum Presets 16(1)(2), 64(1)(3), or 60(4) Maximum Patterns (5)3 Quick Set Menu Not sup
Performance Notes The following considerations should be made when using the SpeedDome Ultra VII Day/Night camera dome in a SensorNet or RS-422 enviro
APPENDIX B Manchester Command Summary This appendix summarizes the Manchester controller commands used with the Configuration Utility. It also provid
Command Summary The following table lists the commands to operate the configuration utility when the dome is installed in a Manchester environment.
Additional Manchester Commands The following tables summarize the special commands available when using the dome in a Manchester network. These comman
Supported Controllers The following Manchester controllers are compatible with SpeedDome Ultra VII Day/Night: Controller Presets Patterns Quick Se
APPENDIX C Pelco Coaxitron and “P” Protocols Command Summary This appendix summarizes the SpeedDome Ultra VII features that are supported by the Pelc
Supported SpeedDome Ultra VII Features The following SpeedDome Ultra VII Day/Night features are supported with Coaxitron and P protocols: • 10X digit
Pelco Command Summary The following table lists the commands to operate the configuration utility when the dome is installed in a Pelco environment. I
Text Conventions This book uses text in different ways to identify different kinds of information. Bold Italics Used for terms specific to the system,
Performance Notes The following SpeedDome Ultra VII features are not supported with the Pelco protocols: • PAL video format. This will be supported a
Setting Left and Right Scan Limits Scan Limits allow you to set left and right boundaries for use with the Auto Scan, Frame Scan, and Random Scan fun
Activating Frame Scan Frame Scan pans between the left and right scan limits, pausing briefly (3 seconds) at each frame. A frame is equivalent to appr
APPENDIX D Panasonic Up-the-Coax (UTC) Protocol Command Summary This appendix summarizes the SpeedDome Ultra VII features that are supported by the P
Supported SpeedDome Ultra VII Day/Night Features The following SpeedDome Ultra VII Day/Night features are supported with the UTC (Up-the-Coax) protoc
Panasonic UTC Command Summary The following table lists the commands to operate the configuration utility when the dome is installed in a Panasonic U
Performance Notes When selecting a dome, a 3- to 5-second delay is necessary for the Panasonic multiplexer to properly identify the dome type. If the
5. Use the joystick to move the highlight to Presets. Press Set to select. The Select Preset to Program screen displays. SELECT PRESET TO PROGRAM PR
NOTES: D–6 SpeedDome Ultra VII Day/Night Operator's Manual
APPENDIX E AD Up-the-Coax (UTC) Command Summary This appendix summarizes the AD-UTC controller commands used with the Configuration Utility. It also
Kommentare zu diesen Handbüchern